Experience since 2017 in solar energy and Online UPS systems
We measure your loads with Fluke instruments, design your system and its mounting structure to engineering standards, then install it or supervise its installation and keep it maintained. One engineering team for residential, commercial and industrial systems.
From load measurement and design to installation, supervision and maintenance. One engineering team and one point of responsibility for residential, commercial and industrial systems.
Complete system engineering based on your real consumption: sizing panels, inverter and batteries, calculating cable sections and protection, and laying out the array for maximum yield.
We measure your actual electrical loads with professional Fluke instruments to find peak demand, running current and power quality, so the system fits your needs: not oversized and costly, not undersized and tripping.
We design steel mounting structures to engineering standards, calculating wind load, panel weight and the optimal tilt angle, so the structure stays solid and safe on the roof or ground for years.
Turnkey installation of residential, commercial and industrial systems: structures, panels, inverters, batteries, wiring and protection, followed by testing, commissioning and handover.
If you have your own installer or contractor, our engineers supervise the work step by step and verify it matches the design and standards before commissioning, so you receive a sound, reliable system.
Scheduled and emergency maintenance for residential, commercial and industrial systems, including ones installed by others: panel cleaning, inverter, battery and connection checks, and fixing any drop in output.
We have worked in solar energy and Online UPS systems since 2017. We have more than 150 systems in operation, with an issue rate no higher than 3%, supported by our technical support and maintenance.
No guesswork: we measure your real loads with professional instruments before any design.
System and structure are engineered for Iraq's heat, dust and wind.
One company handles every stage, so you always know who is responsible.
Panels, inverters and batteries with official warranty, and an itemised quote with no surprises.
Our engineer visits, measures your loads with Fluke instruments and surveys the roof or ground.
We design the electrical system and the structure, and give you an itemised quote.
We install the full system, or supervise your team so the work matches the design.
We test, commission and hand over the system, then keep it maintained.
Enter the amps you need, the same way you count them on a generator subscription, or tap your appliances to add them. The matching system appears instantly.
Scenes from our work, from assembling structures and mounting panels to connecting inverters and batteries.
A front view of the rooftop solar array.
A battery bank with inverters and cable distribution.
Preparing the steel sections on the roof.
Three inverters with energy storage units.
People at one of the Ur Gate work sites.
A view of the panels and their supporting frame.
Preparing and delivering panels before installation.
The mounting frame during rooftop assembly.
A close view of breakers and connections inside the panel.
Inverters and batteries alongside the protection panel.
We offer solar system design, load measurement with Fluke instruments, panel mounting structure design to engineering standards, full installation, installation supervision, and maintenance for all residential, commercial and industrial systems.
Because good design starts with real numbers. Fluke instruments accurately measure current, power and peak demand, so we size panels, inverter and batteries correctly and avoid a system that is oversized and costly or undersized and shuts down under heavy load.
Add up the amps of the appliances you run at the same time, as you would for a generator subscription. At 220 V, 1 A is about 220 W, so a 10 A load is roughly 2.2 kW. Multiply by daily hours of use to get consumption, which sets the number of panels and the inverter and battery size. Try the amp calculator on this page; final sizing follows a Fluke load measurement.
Inverters: Deye, AUXSOL, Solis, ALP Solar, SRNE, Luxpower, Sungrow, GoodWe and SAJ. Batteries: Bett Energy, SVOLT, Deye, Dyness, Lithtec, BasenGreen, ALP Solar, Sungrow and AUXSOL. Panels: LONGi, AIKO, JinkoSolar and JA Solar. We use ABB electrical and protection equipment in our systems.
Yes. Structures are designed with calculations covering panel weight, wind load and the optimal tilt and orientation for the site, with steel sections and fixing methods chosen for the roof or ground.
Yes. We provide engineering supervision, checking the work against the design and safety standards and inspecting the system before start-up.
Yes. We maintain residential, commercial and industrial systems regardless of who installed them, from cleaning and routine checks to fault diagnosis and repair.
Cost depends on your actual loads, hours of use and battery type. After measuring your loads on site we provide an itemised quote before any commitment.
On-grid systems work with the national grid without batteries, off-grid systems run on batteries without the grid, and hybrid systems combine both, which suits most homes and shops in Iraq.
Quality panels last 25 years or more, and lithium (LiFePO4) batteries typically last 10 years or more depending on use and maintenance.
Book a free site visit and load study today.
Leave your details and one of our engineers will contact you shortly.
Baghdad, Karrada, Al-Wathiq Square, Street 42
